The FIA has published details of the tougher floor tests Formula 1 teams are required to conform to during the 2023 season.
Revised floor deflection tests were introduced through a technical directive at the Belgian Grand Prix in August. The change was provoked by concerns some teams had designed their floors in order to satisfy the existing load tests while allowing flexibility in other areas.
The floor deflection test defined in the 2023 rules specifies a dozen points on the floor where a load will be applied in order to ensure the movement of the floor does not exceed 8mm. The rules empower the FIA to “require load points to be moved if, in their view, the load location or the floor shape has been specifically designed to permit greater levels of outboard floor flexibility in untested regions of the floor.”
In order to accurately measure the extent of any deflection, the floors will be laser scanned when loads are applied to them.
Other changes to the 2023 rules relating to teams’ floors have previously been announced, including an increase in the height of the floor edges, which have been raised by 15mm. The under-floor diffuser throat is also being raised, as part of a package of changes intended to prevent cars ‘porpoising’ next year.
The FIA has also revised the rules restricting how teams may change their homologated gearbox designs in 2023. Previously changes were only allowed “to resolve reliability problems” or “for cost saving” reasons. From next year teams will also be allowed to alter their gearbox designs “in the case of materials, processes or proprietary parts becoming unavailable or having their use restricted for health and safety reasons.”
Advert | Become a RaceFans supporter and
Revised floor deflection test regulation
The revised clause (c) of article 3.15.7 of the 2023 Technical Regulations defines the test which will be applied to the outboard edge of cars floors:
The outboard edge of the Floor Bodywork Group may deflect no more than 8mm in Z at any point between XR = -1260 and XR = -350 when a distributed load of [0, 0, -600]N is applied to each side of the car.
The load will be applied simultaneously at 6 points on each side of the car, nominally at: [XR, Y] = [-480, 652.2], [-635, 686.3], [-790, 714.4], [-945, 736.7], [-1100, 753.3], and [-1255, 764.2]. A 2mm tolerance on position will be permitted for manufacturing reasons.
When viewed from above, and with the Floor Bodywork Group as fully defined in Article 3.5.6 in place, nothing other than the bodywork may be visible within 15mm of any load application point. A load application point that does not meet this requirement may be moved, in X and/or in Y, by the minimum amount necessary to comply. The FIA may require load points to be moved if, in their view, the load location or the floor shape has been specifically designed to permit greater levels of outboard floor flexibility in untested regions of the floor.
Once the load application positions are fully defined, Teams must provide a suitable means of applying the load to the upper surface of the bodywork. The load will be applied through a rod of diameter 2.3mm. Details of this arrangement are provided in the appendix to the Technical and Sporting Regulations. The contact of any load-spreader with the bodywork must lie within a cylinder of diameter 25mm, coaxial with the load application axis. If the Team’s preferred method requires through-holes, these holes must be sealed on either or both of the upper and lower surfaces at all times the car is on the circuit and during any assessment of any visibility from above around load application points.
Loads will be applied to these rods in two stages:
i. [0, 0, -50]N to each load application point to give 300N per side.
ii. [0, 0, -100]100N to each load application point to give 600N per side.
Deflection will be measured by laser scanning of the bodywork at each loading stage.
Advert | Become a RaceFans supporter and
2023 F1 season
- Haas present “modernised” livery reflecting new title sponsor
- RB18 clones? ‘Fake’ reveals? What to look for as F1 launch season starts today
- No 2023 car at Red Bull’s Friday launch but Ford rumours grow
- Haas banks on experienced line-up as it seeks another step forward in 2023
- Reports Ferrari engine has gained 30bhp are a “joke” – Vasseur